Wow, lots of conversation. Let me explain my intentions about prefabricated chimney chase inspections. This is my experience doing this work on subrogation cases concerning prefab chases. I started to write a response, but it went on way too long. I've done this work since 1994, and the last was in California in 2013, so I have some history doing it. If you are interested in learning how I do them and my answer to your questions concerning entry holes, getting around inside the chase, dimensions, lighting issues, borescopes, firestops, etc. Keep Reading. 1) Yes, in my opinion, it is a level 3 inspection 2) Intended Purpose: If your intentions are replacement of the existing unit, it would be helpful for a chimney contractor to “see the interior” before setting a saw-z-all to it. (Electrical wires, gas piping, water pipes, etc.) 3) What is real: All of us understand that prefab chases especially track homes, are done by the lowest bidder; therefore, corners are likely to be cut. So, if your gut is telling you something doesn't look or feel right, you have the opportunity to offer a selective service to evaluate the interior without destruction. (Especially if chase covers are sealed well.) 4) Experience: I did 45 such inspections in the state of NJ several years ago and went through the side shoulder, through vinyl siding, and in some cases through the shingles on the roof near the chase to inspect these areas. I can tell you there were many things covered up that caused hidden water issues within these homes, along with a worker stuffing their lunch bag and hoagie wrapper right behind the firebox, so it was in direct contact with the unit and the back OSB wall!! 5) Experience: I also have experience with Randy Brooks in California (45 units). We took many photos to see the areas around gas lines, outside air, and critter presence. Check with Randy on his take about doing them. 6) Dimensions: As far as taking dimensions, the camera is under 1.5” in diameter, so a 1.5” hole saw will allow the camera to pass. Plus, you can bend it with a gooseneck rod so reaching around the chimney pipe can be done. Since the camera is 1.5”, I use that as my measuring device. If the camera can go through an opening between combustible and pipe with wiggle room, then in most cases, the chimney is 1.75” to 2” away from any combustibles. The same with fireboxes. Plus, in most cases, the manufacturer has instructions on the side of the unit, especially sidewall clearances. 7) Firestops: Should you find firestops (past experience tells me not too many), then your inspection can only go that far, and another entry point might be a consideration. Again, it will go back to how bad you need to see?? Since this is a level 3, there is some leeway on this. That’s why I made an inspection checklist so you can tell the customer what you saw and what you didn’t see. 8) Operations: I place the unit on the roof or chase top and drill the hole into the chase. Then attach the camera to one or two rods and lower the camera cable and rod into the chase. When I reach the top of the firebox, I’m looking directly down. There is enough light from the LEDs to illuminate the area. I check the sides of the firebox and clearances, insulation (or lack of), outside air, gas line entry, and other supports. When you need to look at a 90-degree angle, I push the camera into the firebox and bend the gooseneck. When looking for clearances around chimney pipes, it can be done along with a closeup of the mantel support or creative use of 2x4 construction. 9) Borescopes: I have one from Dewalt that works through a ¾ to 1” hole. Works great, but my light is limited to only a few inches around the head, so positioning the borescope can take a while. It has a place but don’t expect it to illuminate a chase!! 10) Sealing: Usually RTV on the chase around the hole, then a 6x6 alum plate with six screws, then cover the edge with RTV silicone. On wood siding under vinyl, same 6x6 sheet of alum. With six screws. In masonry, stuff the hole with some ceramic blanket then mortar over the top. (Not sold on that one, but it was the best I could come up with at the time.) I use a wonder bar on roofs to pry up a shingle tab and drill the hole. When done RTV around the hole and slide plate under the tab, put a dab of RTV on the underside edge of the raised shingle and press down. Also, there is a company that makes a 1.5” plug out of chrome steel which looked interesting. Plug the hole and add RTV Silicone around the plug, and you're done.
1 Comment
|
AuthorTom Urban has worked in the Chimney and Hearth industry for 40 years. He's been an inventor and manufacturer for 35+ of those years. Archives
October 2023
Categories |